2019年翻译资格英语一级口译练习5

>>翻译资格考试：2019年翻译资格英语一级口译练习5

>>翻译资格精选提升课程

The city water pipes in Rome were usually of baked clay or lead; copper was sometimes used and also hollowed stone. For the large supply conduits leading to the city the Romans used covered channels with free water surfaces， rather than pipes. Perhaps this choice was a matter of economics， for apparently they could make lead pipes up to 15 inches in diameter. While pipes can follow the profile of undulating ground， with the pressure increasing in the lower areas， channels cannot. They must slope continuously downwards， because water in channels does not normally flow uphill; and the grade must be flat， from 1 in 60 in small channels to perhaps 1 in 3，000 in large ones， to keep the water speed down to a few feet per second. Thus the main supply channels or aqueducts had long lengths of flat grade and where they crossed depressions or valleys they were carried on elevated stone bridges in the form of tiered arches. At the beginning of the Christian era there were over 30 miles of these raised aqueducts in the 250 miles of channels and tunnels bringing water to Rome. The channels were up to 6 feet wide and 5 to 8 feet high. Sometimes channels were later added on the tops of existing ones. The remains of some of these aqueducts still grace the skyline on the outskirts of Rome and elsewhere in Europe similar ruins are found.

Brick and stone drains were constructed in various parts of Rome. The oldest existing one is the Cloaca Maxima which follows the course of an old stream. It dates back at least to the third century B.C. Later the drains were used for sewage， flushed by water from the public baths and fountains， as well as street storm run-off.

The truly surprising aspect of the achievements of all the ancient hydraulic artisans is the lack of theoretical knowledge behind their designs. Apart from the hydrostatics of Archimedes， there was no sound understanding of the most elementary principles of fluid behaviour. Sextus Frontinus， Rome’s water commissioner around A.D. 100， did not fully realize that in order to calculate the volume rate of flow in a channel it is necessary to allow for the speed of the flow as well as the area of cross-section. The Romans’ flow standard was the rate at which water would flow through a bronze pipe roughly 4/3 inch in diameter and 9 inches long. When this pipe was connected to the side of a water-supply pipe or channel as a delivery outlet， it was assumed that the outflow was at the standard rate. In fact， the amount of water delivered depended not only on the cross-sectional area of the outlet pipe but also on the speed of water flowing through it and this speed depended on the pressure in the supply pipe.

1. The Romans used all of the following to make water pipes EXCEPT _________.

(A) earth (B) wood (C) copper (D) stone

2. Covered channels were used instead of pipes to supply large quantities of water probably because _________.

(A) the Romans could build them more cheaply

(B) these channels could follow uneven ground more easily

(C) the Romans could not build large pipes

(D) these channels avoided rapid changes of pressure

3. The use of ‘grace’ in line 15 suggests that the aqueducts today are _________.

(A) hideous (B) divine (C) useful (D) attractive

4. In order to calculate the volume of water flowing through a pipe， it is important to know its speed and ________.

(A) the area across the end of the pipe (B) the length of the pipe

(C) the water pressure in the pipe (D) the level from which the water falls

5. The main subject of the passage is concerned essentially with __________.

(A) the classical scientific achievements

(B) the theoretical Greek hydrostatics

(C) the ancient Roman hydraulic system

(D) the early European architectural designing

参考答案：

B A D A C

2019年翻译资格考试时间已经确定，备考的时间越来越紧张，希望以上内容可以对你有所帮助。如需了解更多关于考试的资讯信息、备考技巧、考试模拟试题等内容，请继续锁定坦途网翻译资格考试频道，精彩内容正在更新！